2″ Round Regressed Gimbal

Adjustable yet air-tight without housing needed.

MODEL: 5W: LRG2 | 5.5W: LRG2-HO Category: Adjustable Gimbal

Spec & Sell Sheets

Product Features

Models: 5W: LRG2, High Output 5.5W: LRG2-HO
Type IC Rated – Approved for Direct Contact with Insulation
Air-Tight, Wet Location, Insulated and Non Insulated Ceilings
Superb Light Quality with CRI 90+
Color Temperatures: 2700K / 3000K / 3500K / 4000K / 5000K / Dim to Warm 3000-1800K
Light Output 5W: 2700K – 380 lm, 3000K – 400 lm, 4100K – 430 lm
Light Output 5.5W: 2700K – 450 lm, 3000K – 490 lm, 3500K – 500 lm, 4000K – 530 lm, 5000K – 550 lm, Dim to Warm – 430 lm
External Driver Inside Connection Box – No Junction Box Needed
Default Driver 120V input Triac dimmable with most CL Dimmers
Optional Driver for 5.5W model: 120V-347V input 0-10V Dimmable
Recessed Housing is NOT Required even for Insulated Ceilings
Warranty: 10 Year on Residential, 5 Year on Commercial Installations
cULus Listed, Energy Star (only LRG2-HO and except Dim to Warm)

Where to Buy

Video Overview

Discover Round Regressed Gimbal LED Lighting Fixtures

Technical Specifications

CONSTRUCTION:
2″ Round Regressed Gimbal fixture with integral LEDs. Class 2 Isolated external driver factory installed inside junction box.
One driver for every fixture required.

MOUNTING:
Cut hole in ceiling and snap fixture in opening with attached spring clips.
Ceiling Clearance Required: 1 1/2″ with driver remotely installed, 5″ if driver is next to the fixture.

Default Driver: 120V input Triac Dimmable with most CL dimmers
Optional Driver for 5.5W HO model: 120V-347V input 0-10V Dimmable
Energy Used: LRG2 5W, LRG2-HO 5.5W,
Power factor: > 0.95
Beam Angle: 36° Beam with 20° tilt and 360° rotation
Color Temperatures: 2700K / 3000K / 3500K / 4000K / 5000K / Dim to Warm 3000-1800K
Light Output 5W: 2700K – 380 lm, 3000K – 400 lm, 4100K – 430 lm
Light Output 5.5W: 2700K – 450 lm, 3000K – 490 lm, 3500K – 500 lm, 4000K – 530 lm, 5000K – 550 lm, Dim to Warm – 430 lm
CRI 90+
Ambient Operating Temperature: -40°F (-40°C) to +104°F (+40°C)
Compliance: cULus approved, certified to CSA STD. C22.2 No. 250.0
Rated: Type IC (Direct Contact with Insulation), Energy Star(only LRG2-HO and except Dim to Warm), T24, Air-Tight

DIMENSIONS:

ID 2 1/2″, OD 3″; Thickness 1 3/4″
Cut out: 2 1/2″ to 2 3/4″
Junction Box Dimensions (with driver inside): 2 3/4″ x 2″ x 1 3/4″

Suitable for wet locations and soffit installations.

Installation

ALL FIXTURES MUST BE INSTALLED IN ACCORDANCE WITH CURRENT APPLICABLE ELECTRICAL CODES.

Regressed Gimbal LED Lights Installation:

CONNECTING THE DRIVER:
Open the cover of the junction box. Push and remove the knockout on the side plate. Install standard L16 cable connector. Insert line voltage feed into the cable connector and splice same colour wires using the included quick connectors. Close the cover. Connect the driver to the light fixture – the arrows on the male and female parts of the connector between the driver and the fixture should match. Tighten the connector by hand.

OPTIONS FOR LOCATING DRIVER:

Fixture comes connected to the driver by 15″ long low voltage cable with waterproof connector in the middle.
Depending on where you want the driver to be you have 2 options:

Locate next to the fixture.
Or install all drivers at one location and use low voltage extension cables to the fixtures. Use only extensions provided by the manufacturer. Available jumper cables are 6 feet (1.8m) and 20 feet (6m). Cables are linkable.
Maximum run should not exceed 40 feet (12m).

DIMMING:

We recommend LED/CFL dimmers that have a low range adjustment dial. After all fixtures are connected to the dimmer adjust the dial to the lowest position before the lights start to flicker of shut down. This setting depends on the local voltage and number of fixtures per dimmer.

LIST OF COMPATIBLE DIMMERS

WARNING:
DO NOT USE ANY OTHER DRIVERS EXCEPT THE LOTUS DRIVERS THAT ARE INCLUDED WITH THE FIXTURE.
DO NOT CONNECT MULTIPLE FIXTURES TO ONE DRIVER.
DO NOT OPEN THE LIGHT FIXTURE AND THE SIDE PLATES OF THE DRIVER – NO SERVICEABLE PARTS INSIDE.